morris oxford ser. ii - iii
The illustration No. of the following parts referes to the Original Spare Parts Book
All parts N.O.S.
All parts N.O.S.
Part No. | Illus.No. | Description | Comments | Part in stock | Price Each in Euro | |
1A1546 | AA 13 | Thrower - oil - front | Engine | 3 | ||
1A2028 | AA 11 | Gear for crankshaft | Engine | 1 | 57:00 | |
1A2032 | AA 19 | Plate - camshaft locating = 1G 1361 = 11G 136 | Engine | 1 | ||
1A2064 | AG 11 | Distance piece for bearing - water pump | Engine | 3 | ||
1A2065 | AG 7 | Retainer for felt washer ( inner ) | Engine | 9 | ||
1A2066 | AG 9 | Retainer for felt washer ( outer ) | Engine | 13 | ||
1A2068 | AG 13 | Ring - spring - water pump | Engine | 7 | ||
1A2122 | AB 15 | Cup - valve | Engine | 20 | 1:50 | |
2A136 | AG 37 | Pulley for dynamo = 2A 412 = 2A 864 = 1H 998 | Engine | 1 | 25:00 | |
2A150 | AB 58 | Nut for rocker cover | Engine | 4 | 3:50 | |
2A258 | AB 28 | Screw - rocker shaft ( locating ) | Engine | 2 | ||
2A412 | Ag 37 | Pulley for dynamo = 2A 136 = 2A 864 = 1H 998 | Engine | 1 | ||
2A458 | NA30 | Switch for courtesy light | Switches | 5 | ||
2A552 | AC 12 | Cover front ( with oil catcher & felt ) = 1G 1586 | Engine | 1 | 32:00 | |
2A778 | AG 24 | Wire for bearing ( locating ) - water pump | Engine | 3 | ||
2A816 | AC 34 | Tap - cylinder block drain = 11G 153 = 12G 215 | Engine | 2 | ||
2A864 | AG 37 | Pulley for dynamo = 2A 136 = 2A 412 = 1H 998 | Engine | 1 | ||
2A3254 | FB 86 | Oil seal | Gearbox | 4 | 4:50 | |
2A3255 | F 84 | Retainer for oil seal | Gearbox | 1 | 4:50 | |
2A3256 | F 80 | Bush = 11G 3227 = 22H 29 | Gearbox | 2 | ||
2A6007 | J 3 | Washer ( cork ) | Steering rack | 6 | ||
22A75 | F 93 | Spring - column gear change = 2K 4904 | Gearbox | 14 | ||
AAA3565 | RC 3 Lock - boot lid = ADA 2577 | Boot | 1
| | ||
AAA4144 | RG 94 | Pull & arm rest - (Empire green) = 185839 | Door hinges - Checks - Locks & Trim | 2 | ||
ACA5119 | EE 128 | Clip - pipe to control unit & adaptor = 3H 2963 | Clutch | 1 | ||
ACA5128 | D 28 | Nut for front end | Tank & pipes | 1 | ||
ACA5244 | J 7 | Pad - damper - steering rack | Steering | 5 | ||
ACA5245 | J 10 | Housing for damper pad = ACH 8425 | Steering | 1 | ||
ACA5269 | DA 47 | Rubber - bracket to body bracket | Fuel pump | 17 | 1:50 | |
ACA5271 | HB 23 | Plate - front bracket | Rear sprins | 2 | ||
ACA5308 | page P 1 | Plug - rubber | Wheels | 4 | ||
ACA5380 | AJ 84 | Link - rubber | Engine control mountings | 1 | ||
ACA5399 | D 33 | Nut for front end | Tank & pipes | 8 | 2:50 | |
ACA5402 | D 34 | Nipple for front end | Tank and pipes | 4 | 2:00 | |
ACA5419 | O 36 | Olive - flexible pipe to engine | Instrument panel & instruments | 3 | 1:50 | |
ACB4021 | KA 5 | Spacer - upper link pivot | Torsion bar | 1 | ||
ACB8744 | O 37 | Clip for pipe | Instrument panel & instruments | 19 | ||
ACC8518 | L 5 | Washer for bush retaining - outer | Shock absorber | 4 | ||
ACC8520 | L 4 | Washer for bush retaining - inner | Shock absorbers | 4 | ||
ACH4018 | KA 63 | Bump stop - front | Front suspension | 2
| | |
ACH4029 | KA 10 | Rubber bush - arm to bracket | Front suspension | 1 | ||
ACH4040 | KA 25 | Spacer - lower link pivot = AAA1662 | Torsion bar | 2 | ||
ACH4042 | KA 32 | Eyebolt to frame | Linkage - torsion bar | 2 | ||
ACH4043 | KA 31 | Extension - lower arm -later = ACH5158 | Front suspension | 2 | ||
ACH5069 | HB 13 | Pad for leaf clip ( long ) | Rear spring | SOLD OUT | ||
ACH5108 | MB 15 | Pin - lever to cable | Hand brake cables | 3 | ||
ACH5123 | Bush | 1 | ||||
ACH5142 | FC 52 | Ball joint | Gear change mechanism | 2 | ||
ACH5145 | FC 47 | Bush - for lever selector | Gear change mechanism | 5 | ||
ACH5156 | HB 33 | Shackle pin - rear | Rear springs | 8 | ||
ACH5160 | HB 28 | Pin - front | Shock absorbers | 4 | ||
ACH5175 | RJ 21 | Escutheon - starting handle - bumper | Bumpers & fittings | SOLD OUT | ||
ACH5190 | RJ 39 | Rubber - blade ends to body | Bumpers | 1 | ||
ACH5298 | AL 18 | T - barrel for accelerator cable | Engine controls | 6 | ||
ACH5333 | DD 15 | Stud for air pipe support | Air silencer & cleaner | 2 | ||
ACH5338 | DD 22 | Pipe - air | Air cleaner & silencer | 1 | ||
ACH5391 | L 14 | Absorber assembly - rear - 1st type ( = ACH8509) | Shock absorber | 3 | ||
ACH5441 | page N 8 | Side lamps - RHD | Road lamps | 1 | ||
ACH5444 | page N 8 | Side lamps - LHD | Road lamps | 1 | ||
ACH5669 | DD 23 | Seal - pipe to silencer & cleaner | Air silencer & cleaner | 2 | ||
ACH5675 | FC 65 | Bush for pin - rod selector | Gear change mechanism | 1 | ||
ACH5697 | FC 33 | Lever - selector | Gear change mechanism | 1 | ||
ACH5703 | HA 32 | Seal for brake drum - dust ( large ) | Rear brakes | 2 | ||
ACH5704 | K 29 | Seal - dust - small | Torsion bar | 1 | ||
ACH5708 | DD 13 | Grommet for rod | Air silencer & Cleaner | 4 | ||
ACH5715 | DD 12 | Washer for rod ( fibre ) | Air silencer & cleaner | 1 | ||
ACH5731 | FC 46 | Lever - shifter relay | Gear change mechanism | 1 | ||
ACH5752 | Speed change parts | Speed change mechanism | 1 | |||
ACH5854 | D 31 | Clip for hose | ank & pipes | 5 | ||
ACH5898 | FC 1 | Lever - hand - gear change | Gearbox | 1 | ||
ACH6001 | J 78 | Nut for wheel | Steering | 5 | ||
ACH6009 | J 1 | Housing - rack assembly | Steering | 1 | ||
ACH6011 | J 15 | Pinion - steering | Steering | 8 | ||
ACH6015 | page J 1 | Tie rod assembly | Steering | 2 | ||
ACH6020 | J 25 | Rod - bare - tie rod | Steering | 1 | ||
ACH6056 | Switch - column | Gear change mechanism | 1 | |||
ACH6095 | FC 2 | Knob - column gear change lever | Gear change mechanism | 1 | ||
ACH6096 | FC 4 | Pin - pivot - gear change | Gearbox | 2 | ||
ACH6097 | FC 6 | Shim for pivot pin - gear change | Gearbox | 2 | ||
ACH6098 | FC 7 | Screw for pivot pin - gear change | Gearbox | 2 | ||
ACH6100 | FC 11 | Spring - lever return | Gear change mechanism | 3 | ||
ACH6101 | FC 10 | Pin - pivot - rod assembly control | Gearbox | 2 | ||
ACH6105 | FC 23 | Pin - pivot - control rod | Gear change mechanism | 5 | ||
ACH6107 | FC 43 | Bush - spherical - bearing - support assembly = 132478 | Gear change mechanism | 14 | ||
ACH6170 | page J 2 | Washer for ball socket | Steering | 10 | ||
ACH6173 | J 81 | Washer for greaser ( fibre ) | Steering | 6 | ||
ACH8295 | AJ 25 | Distance piece | Engine mountings | 1 | ||
ACH8364 | DD 10 | Rubber bush for steady bracket | Air silencer & cleaner | 6 | ||
ACH8390 | AL 2 | Pad - pedal accelerator | Engine controls | 1 | ||
ACH8425 | J 10 | Housing for damper pad = ACA 5245 | Steering | 1 | ||
ACH8490 | DD 8 | Sleeve - air cleaner to pipe | Air silencer & Cleaner | 4 | ||
ACH8508 | MB 23 | Spring for adjustment | Handbrake cables | 6 | ||
ACH8509 | L 14 | Absorber assembly - rear = ACH5391 | Shock absorber | 1 | ||
ACH8527 | FA 45 | Knob for change speed lever = 13H 94 | Gearbox | 1 | ||
ACH8589 | FA 160 | Draught excluder - gear lever | Gearbox | 1 | ||
ACH8769 | FC 19 | Bolt - plunger spring retaining | Gear change mechanism | 10 | ||
ACH8774 | FC 16 | Loch washer for plunger - column change | Gear change mechanism | 4 | ||
ADA1861 | RN 47 | Catch for lid | Fascia details | 1 | ||
ACA2490 | RH 54 | Spring for safety catch | Bonnet & wings | 3 | ||
ACA2577 | RC 3 | Lock - boot lid = AAA 3565 = HD 441 | Boot | 1 | ||
ADB4492 | RR 43 | Clip - tube to blower & heater | Heater & blower | 2 | ||
ADH582 | RH 9 | Motif - bonnet - upper portion - early | Bonnet & wings | SOLD OUT | ||
ADH583 | RH 10 | Motif - bonnet - lower portion - early | Bonnet & wings | 2 | ||
ADH635 | RH 2 | Hinge assembly for bonnet - RH | Bonnet & wings | 1 | ||
ADH662 | O 29 | Ammeter = 37H5189 | Instrument panel & instruments | 3 | ||
ADH669 | C 33 | Finisher - grille to wing RH - black | Cooling system | SOLD OUT | ||
ADH670 | C 33 | Finisher - grille to wing LH - black | Cooling system | SOLD OUT | ||
ADH672 | RH 88 | Nameplate " OXFORD" | Bonnet & wings | SOLD OUT | ||
ADH835 | RF 14 | Capping for finisher | Window & window mechanism | 3 | ||
ADH1458 | RG 6 | Link assembly for door - check | Door hinges-checks-locks- & trim | 1 | ||
ADH2470 | R 9 | Weatherstrip - LH outer RH inner = ADH 2473 | Window & window mechanism | SOLD OUT | ||
ADH2471 | Weatherstrip - RH outer LH inner = ADH 2472 | Window & window mechanism | SOLD OUT | |||
ADH2472 | RF 13 | Weatherstrip - RH outer LH inner = ADH 2471 | Window & window mechanism | SOLD OUT | ||
ADH2473 | R 9 | Weatherstrip - LH outer & RH inner = ADH 2470 | Window & window mechanism | SOLD OUT | ||
ADH2542 | C 2 | Clip for vertical members | Cooling system | SOLD OUT | ||
ADH4502 | NA 9 | Ignition switch | Switches | 1 | ||
ADH5492 | NE 43 | Wiper arm - LH = 57H 5291 | Windscreen | 2 | ||
ADH5591 | RG 88 | Clip for finisher - door trim pad | Door hinges-Locks-trim | 18 | ||
ADH5679 | RN 4 | Mask - instrumental panel | Fascia details | 1 | ||
ADH5825 | RG 76 | Striker - door lock - front - RH | Door hinges-Locks-Trim | 2 | ||
ADH5830 | page N 13 | Wheelbox wipers - 72608B | Windscreen wipers | 2 | ||
ADH6555J | RP 5 | Sun visior - Grey | Sundries | 2 | ||
ADH6576 | RH 24 | Motif - bonnet - upper portion | Bonnet & wings | 1 | ||
ADH6577 | RH 31 | Motif - bonnet - lower portion | Bonnet & wings | 1 | ||
ADH6758 | RN 42 | Hinge - glove box lid | Fascia & details | |||
ADH8493 | RL 16 | Clip - moulding to wing = 1H 5611 | Fascia details | 54 | ||
AEC339 | AA 29 | Joint for tensioner | Engine | 1 | ||
AEG3101 | FA 38 | Dowel for change speed - lever tower | Gearbox | 5 | ||
AJA5081 | NB 4 | Screw - rim fixin | Headlamps | 7 | ||
AJD8104Z | HC 7 | Nut for bolt | Rear springs | 5 | ||
AJD8105Z | AJ 39 | Nut ( to brake plate ) | Rear brakes | 10 | ||
AJH5059 | ND 11 | Switch - trafficator | Direction indicators | SOLD OUT | ||
AJH5068 | ND 17 | Contact - horn - bottom | Trafficators & horn controls | 1 | ||
AJH5073 | AE 13 | Spring - oil filters A.C. | Engine | 2 | ||
AJH5096 | NC 2 | Lens - rear lamp - RH early | Road lamps | 1 | ||
AJH5097 | NC 2 | Lens - rear lamp - LH early | Road lamps | 1 | ||
AJDH5098 | NC 3 | Rubber- glass seating - rear lamp | Road lamps | 4 | ||
AJH5101 | NB 30 | Rim - chrome - side lamp | Road lamps | 1 | ||
AJH5103 | NB 32 | Glass - sidelamp | Road lamps | 5 | ||
AJH5116 | ND 24 | Lever - trafficator switch | Direction indicators | SOLD OUT | ||
AJH5117 | ND 28 | Plate & sleeve - stator - steering tube | Direction indicators | 1 | ||
AJH5126 | NC 4 | Bulb holder - RH - rear lamp | Road lamps | 1 | ||
AJH5127 | NC 4 | Bulb holder - LH - rear lamps | Road lamps | 1 | ||
AJH5111 | RQ 23 | Cable ( inner ) - control | Heater & blower | 2 | ||
AKH461 | ND 23 | Rotor - trafficator & flasher switch | Direction indicators | 2 | ||
ARB507 | D 3 | Plug & strainer assembly - drain | Tank & pipes | 5 | ||
ARB508 | D 4 | Washer for plug | Tank & pipes | 7 | ||
ARH517 | C 4 | Washer for drain tap - radiator | Cooling system | 90 | ||
ARH618 | C 15 | Member - grille - top -Chromed plated | Cooling system | SOLD OUT | ||
ARH624 | C 17 | Member - grille vertical (short) | Cooling system | 1 | ||
ARH701 | RF 35 | Bracket for hinge - upper - RH | Window & window mechanism | 1 | ||
ARH702 | RF 35 | Bracket for hinge - upper - LH | Window & window mechanism | 1 | ||
ARH715 | RF 16 | Handle - locking - RH | Window & window mechanism | SOLD OUT | ||
ARH717 | RF 18 | Pin for handle retaining | Window & window mechanism | 32 | ||
ARH749 | RF 20 | Screw - bracket to frame | Window & window mechanism | 5 | ||
ARH1050 | C 3 | Tap - drain - radiator | Cooling system | 1 | ||
ATA7043 | H 22 | Bolt - crown wheel to cage | Rear axle | 6 | ||
ATA7047 | H 29 | Oil seal ( for pinion ) | Rear axle | 2 | ||
ATB4055 | K 8 | Rubber seal for lower link | Swivel pins & brakes | 10 | ||
ATB4056 | K 1 | Swivel pin - RH | Swivel pins & brakes | 1 | ||
ATB4057 | K 1 | Swivel pin - LH | Swivel pins & brakes | 1 | ||
ATB4064 | page K 1 | Lever - steering - RH | Front suspension | 5 | ||
ATB4074 | K 16 | Nut for wheel stud | Front suspension | 1 | ||
ATB4098 | K 30 | Cap - grease retaining | Front suspension | SOLD OUT | ||
ATB4140 | K 2 | Link - upper - RH = ATB 4200 | Swivel pins & brakes | 5 | ||
ATB4141 | K 2 | Link - upper - LH = ATB 4201 | Swivel pins & brakes | 2 | ||
ATB4145 | K 5 | Link - lower - RH | Swivel pins & brakes | 2 | ||
ATB4146 | K 5 | Link - lower - LH | Swivel pins & brakes | 1 | ||
ATB4150 | Rubber seal for upper link = ATC 4056 | Front suspension | SOLD OUT | |||
ATB4200 | K 2 | Link - upper - RH - LATE = ATB 4140 | Swivel pins & brakes | 2 | ||
ATB4201 | K 2 | Link - upper - LH =ATB 4141- late | Swivel pins & brakes | 4 | ||
ATB7105 | H 28 | Shim outer bearing - 0.010" | Rear axle | 9 | ||
ATB7107 | H 28 | Shim - outer bearing - 0.020" | Rear axle | 5 | ||
ATB7229 | H 42 | Ring - oil seal | Rear axle | 2 | ||
ATC4056 | K 4 | Rubber seal for upper link = ATB 4150 | Front suspension | 4 | ||
AUA839 | DA 8 | Disc - valve | Carburetter | 18 | ||
AUA887 | DA 3 | Union - inlet | Carburetter | |||
AUA1464 | DA 11 | Filter | Carburetter | 1 | ||
AUA1479 | DA 7 | Washer for cage | Carburetter | 13 | ||
AUC1152 | DB 65 | Pin - for hinged lever | Carburetter | 4 | ||
AUC1158 | DB 21 | Spring for gland | Carburetter | |||
AUC1163 | DC 57 | Cap nut for lid | Carburetter | 1 | ||
AUC1167 | DB 8 | Spring for piston ( yellow ) | Carburetter | 2 | ||
AUC1223 | DC 51 | Float | Carburetter | 1 | ||
AUC1358 | DB 44 | Screw for disc | Carburetter | 11 | ||
AUC1412 | DC 53 | Washer for lid | Carburetter | 9 | ||
AUC1981 | DC 55 | Lever - hinged | Carburetter | 4 | ||
AUC2117 | DB 17 | Ring - sealing - aluminium | Carburetter | 5 | ||
AUC2119 | DB 20 | Washer for gland ( brass ) | Carburetter | 10 | ||
AUC2122 | DB 23 | Washer for top bearing | Carburetter | 3 | ||
AUC2139 | DB 66 | Filter | carburetter | 1 | ||
AUC2149 | DB 25 | Screw for needle ( locking ) | Carburetter | 1 | ||
AUC2175 | DB 10 | Screw - chamber to body | Carburetter | 4 | ||
AUC2381 | DB 29 | Pin to lever = AUC 5009 | Carburetter | 2 | ||
AUC2451 | DB 54 | Spring for top lever screw | Carburetter | 4 | ||
AUC2521 | DB 53 | Screw for top lever adjusting | Carburetter | 4 | ||
AUC2694 | DB 81 | Bolt for lever ( clamp ) | Carburetter | 1 | ||
AUC2698 | DB 67 | Bolt - banjo | Carburetter | 1 | ||
AUC3117 | DB 27 | Spring - lever return = AUC 4667 | Carburetter | 2 | ||
AUC3232 | DB 14 | Nut - gland seating | Carburetter | 3 | ||
AUC3471 | DB 38 | Bolt - pivot | Carburetter | 2
| | |
AUC4667 | DB 27 | Spring - lever return = AUC 3117 | Carburetter | 2 | ||
AUC4848 | DB 40 | Washer for bolt ( aluminium ) | Carburetter | 5 | ||
AUC5009 | DB 31 | Pin to lever =AUC 2381 | Carburetter | 2 | ||
AUC6906 | page D 9 | Kit - washer ( No. 6 ) | Carburetter | 5 | ||
AUC8092 | page D 12 | Heater - carburetter suction chamber | Carburetter | 3 | ||
AUC8103 | DB 6 | Cap assembly | Carburetter | 1 | ||
AUD1149 | DB 24 | Needle - EB - std. | Carburetter | 1 | ||
AUD1270 | DB 24 | Needle - MO - weak | Carburetter | 2 | ||
AUD1272 | DB 24 | Needle - M8 - std. | Carburetter | 2 | ||
1B1479 | AB 13 | Oil seal - valve | Engine | 11 | ||
1B1807 | AB 2 | Guide - valve inlet = 1G 2882 = 11G 313 | Engine | 4 | ||
1B3343 | F 110 | Oil seal | Gearbox | 2 | ||
1B8347 | AJ 53 | Bush - steady rod to gearbox | Engine mountings | 4 | ||
CHS2513 | F 22 | Stud ( to casing ) | Gearbox | 6 | ||
CLZ0408 | RQ 35 | Pin - flap end ( pivot ) = CLZ 0417 | Heater & blower | 5 | ||
CLZ0417 | RQ 35 | Pin - flap end ( pivot ) = CLZ 0408 | Heater & blower | 5 | ||
CLZ0517 | EA 17 | Pin - push-rod to clutch lever ( clevis ) | Clutch | 1 | ||
FNN2412 | K 23 | Nut for stub shaft - LHT | Swivel pins & brakes | 3 | ||
FNZ205 | AJ 80 | Locknut ( RHT ) | Engine | 19 | ||
1G765 | AA 10 | Bush for 1st motion shaft | Engine | 41 | ||
1G1319 | AA 17 | Washer for nut ( lock ) - crankshaft | Engine | 4 | ||
1G1361 | AA 19 | Plate - camshaft locating = 1A 2032 = 11G 136 | Engine | 1 | ||
1G1452 | AA 52 | Valve - oil release - oil pump | Engine | 1 | ||
1G1586 | AC 12 | Cover - front ( with oil catcher & felt ) = 2A 552 | Engine | 1 | ||
1G2300 | AB 21 | Bracket - rocker shaft ( tapped ) = 11G 218 | Engine | 3 | ||
1G2303 | AG 6 | Distance piece - water pump | Engine | 2 | ||
1G2310 | page A 21 | Rep. kit - water pump | Engine | 2 | ||
1G2314 | AB 8 | Valve - inlet = 11G 310 | Engine | 8 | ||
1G2315 | AB 9 | Valve - exhaust = 1H 1330 | Engine | 3 | ||
1G2317 | AA 17 | Pulley for crankshaft = 1G 2713 = 11G 81 | Engine | 1 | ||
1G2340 | page A 8 | Camshaft gera & tensioner ring assembly = 11G 135 = 11G 203 = 48G 175 | Engine | 1 | ||
1G2377 | AB 11 | Shroud & oil seal - retainer for valve guide | Engine | SOLD OUT | ||
1G2380 | AB 39 | Push rod | Engine | 8 | ||
1G2402 | AG 51 | Blade - fan = 11G 232 | Engine | 1 | ||
1G2575 | AA 38 | Tappet - std. = 11G 240-early B-series | Engine | 19 | ||
1G2623 | AH 19 | Distance piece for carburetter = AA 291 | Manifold | 1 | ||
1G2624 | page A 24 | Joint washer - carburetter to manifold | Engine service parts | 1 | ||
1G2713 | AA 14 | Pulley for crankshaft = 1G 2317 = 11G 81 | Engine | 1 | ||
1G2881 | page A 25 | Spring - valve | Engine | 1 | ||
1G2882 | AB 2 | Guide - valve inlet = 11G 313 = 1B 1807 | Engine | 4 | ||
1G2887 | page A 25 | Spring - valve = 12H 650 | Engine | 28 | ||
1G3268 | F 68 | Peg - washer locking | Gearbox | 1 | ||
1G3331 | F 64 | Ring - interlocking 2nd 3rd speed gear | Gearbox | 1 | ||
1G3492 | F 57 | Washer - rear thrust | Gearbox | 1 | ||
1G3576 | F 47 | Washer - front thrust | Gearbox | 1 | ||
1G3597 | F 70 | Synchronizer - 3rd & 4th speed | Gearbox | 1 | ||
1G3598 | F 74 | Coupling - sliding 3rd & 4th speed | Gearbox | |||
1G3612 | F 86 | Washer for nut ( locking ) = 11G 3226 | Gearbox | 1 | ||
1G3668 | F 24 | Breather - gear change column | Gearbox | 1 | ||
1G3701 | F 78 | Pinion - speedometer = 11G 3042 = 11G 3264 = 1H 3241 | Gearbox | 2 | ||
1G3704 | F 58 | Bush - selector lever | Gearbox | 2 | ||
1G3709 | FA 59 | Circlip for selector lever bush | Gearbox | |||
1G3741 | F 114 | Lever - outer | Gearbox | 1
| | |
1G7305 | H 47 | Washer for hub nut ( lock ) = 1G 7584 | Gearbox | 3 | ||
1G7435 | H 41 | Stud - for road wheel | Rear axle | 6 | ||
1G7448 | H 3 | Nut for bearing ( RHT ) | Rear axle | 1 | ||
1G7582 | H 3 | Nut for bearing ( LHT ) | Rear axle | 1 | ||
1G7584 | H 47 | Washer for hub nut ( lock = 1G 7305 | Gearbox | 2 | ||
1G7600 | H 20 | washer - bearing packing - 0.010" | Rear axle | 1 | ||
1G8781 | AJ 58 | Buffer | Engine mountings | 4 | ||
1G9380 | AJ 36 | Rubber | Gearbox mountings | 4 | ||
8G548 | Boot - terminal - start switch | Electrical equipment | 4 | |||
8G555 | H 44 | Oil seal | Rear axle | 8 | ||
8G619 | AE 9 | seal - top - oil filter - Tecalemit | Engine | 6 | ||
8G724 | page A 21 | Hub for pulley - water pump | Engine | 1 | ||
8G2080 | AA 7 | Bearing for connecting rod = 8G 2207 | Engine | 2 | ||
8G208040 | AA 7 | Bearing for connecting rod +0.40" | Engine | 2 | ||
8G2081 | AA 45 | Bearing - main - std. = 8G2175 | Engine | 1 | ||
8G2175 | AA 45 | Bearing - main - std. = 8G 2081 | Engine | 1 | ||
8G217530 | AA 45 | Main bearing +0.30" 1489 cc | Engine | 1 | ||
8G217540 | AA 45 | Main bearing + 0.40" 1489 cc | Engine | 3 | ||
8G2176 | A 22 | Liner for camshaft bearing | Engine | 1 | ||
8G2207 | A 7 | Bearing for connecting rod = 8G 2080 | Engine | 2 | ||
8G2310 | page A 21 | Kit - water pump - repair | Engine: | 1 | ||
8G8224 | page M 2 | Master cylinder repair kit | Clutch & brake cylinder | 6 | ||
8G8245 | page K 2 | Front wheel cylinder repair kit | Front brakes | SOLD OUT | ||
11G81 | AA 14 | Pulley for crankshaft = 1G 2317 = 1G 2713 | Engine | 1 | ||
11G135 | AA 22 | Camshaft gear tensioner ring = 1G 2340 = 11G 203 = 48G 175 | Engine | 1 | ||
11G136 | AA 19 | Plate - camshaft locating = 1A2032 = 1G 1361 | Engine | 1 | ||
11G153 | AC 34 | Tap - cylinder block drain = 2A816 = 12G 215 | Engine | 2 | ||
11G193 | AB 3 | Guide - valve exhaust | Engine | 5 | ||
11G203 | AA 22 | Camshaft gear & tensioner ring = 1G 2340 = 11G 135 = 48G 175 | Engine | 1 | ||
11G203 | A 22 | Plug - oil filler | Engine | 2 | ||
11G218 | AB 21 | Bracket - rocker shaft = 1G 2300 | Engine | 3 | ||
11G232 | A G 51 | Blade - fan = 1G 2402 | Engine | 1 | ||
11G240 | AA 38 | Tappet - std. = 1G2575 | Engine | 7 | ||
11G241 | AA 39 | Push rod = 1G 2380 | Engine | 6 | ||
11G310 | AB 8 | Valve - inlet = 1G 2314 | Engine | 8 | ||
11G313 | AB 2 | Guide - valve inlet = 1G 2882 = 1B 1807 | Engine | 4 | ||
11G2007 | NA 27 | Switch for headlamp dipping | Switches | 1 | ||
1G3022 | F 73 | Baulk ring - 3rd & 4th speed gears | Gearbox | 8
| ||
11G3042 | F 78 | Pinion - speedometer = 1G 3701 = 11G 3264 = 1H 3241 | Gearbox | 2 | ||
11G3147 | F 17 | Oil seal assembly = 11G 3270 = 1H 3339 | Gearbox | 21 | ||
11G3226 | F 86 | Washer for nut ( locking ) = 1G 3612 | Gearbox | 1 | ||
11G3227 | F 80 | Bush = 2A 3256 = 22H 29 | Gearbox | 2 | ||
11G3264 | F 78 | Pinion - speedometer = 1G 3701 = 11G 3042 = 1H 3241 | Gearbox | 2 | ||
11G3270 | F 17 | Oil seal assembly = 11G 3147 = 1H 3339 | Gearbox | 2 | ||
11G3032 | F 34 | Cover - dust casting | Gearbox | 1 | ||
11G215 | AC 34 | Tap - cylinder block drain = 2A 816 = 11G 153 | Engine | 2 | ||
48G175 | AA 22 | Camshaft gear & tensioner ring = 1G 2340 = 11G 135 = 11G 203 | Engine | 1 | ||
48G207 | AB 26 | Sceew - tappet adjusting | Engine | 7 | ||
1H353 | A 23 | Joint for front & rear main bearing cap | Engine | 7 | ||
1H577 | A 29 | Pin - gudgeon -std. = 1H 1113 | Engine | 3 | ||
1H898 | AF 41 | Washer for banjo union - oil filter | Engine | 8 | ||
1H922 | AF 42 | Adaptor for poil pipe - oil filter | Engine | 1 | ||
1H945 | B 1 | Distributor - DM 2 | Electrical equipment | 1 | ||
1H998 | AG 37 | Pulley for dynamo = 2A 136 = 2A 412 = 2A 864 | Engine | 1 | ||
1H1113 | A 29 | Pin - gudgeon - std. = 1H 577 | Engine | 3 | ||
1H1152 | page A 21 | Vane - water pump | Engine | 1 | ||
1H1330 | AB 9 | Valve - exhaust =1G 2315 | Engine | 3 | ||
1H3241 | F 78 | Pinion - speedometer = 1G 3701 = 11G 3042 = 11G 3264 | Gearbox | 2 | ||
1H3257 | FA 68 | Fork - 3rd & 4th speed | Gearbox | 1 | ||
1H3339 | F 17 | Oil seal assembly = 11G 3147 = 11G 3270 | Gearbox | 2 | ||
1H3364 | F 24 | Breather - gear change column = 1G 3668 | Gearbox | 1 | ||
1H5611 | page R 29 | Clip - moulding to wing = ADH 8493 | Fascia details | 21 | ||
2H326 | AA 15 | Key for crankshaft gear & pulley | Engine | 6 | ||
2H4185 | NA 13 | Lock - barrel = 7H 9830 | Switches | 1 | ||
2H4905 | AA 26 | Timing chain | Engine | 1 | ||
2H4992 | Connector for cable - 6 way | Cables & connections | SOLD OUT | |||
3H550 | EA 12 | Gasket for connection - small | Clutch slave cylinder | 10 | ||
3H576 | page A 14 | Washer for tap - drain | Engine | 2 | ||
3H950 | NA 2 | Coupling for starter switch | Switches | 1 | ||
3H1655-58 | B 45-48 | Ferrule for HT cable - No. 1 - 4 | Ignition | SOLD OUT | ||
3H2138 | B 7 | Plate - clamping | Distributor | 2 | ||
3H2695 | B 25 | Terminal | Ignition coil | 4 | ||
3H2836 | AG 55 | Transmitter - thermal = 17H 575 | Transmitter | SOLD OUT | ||
3H2837 | page A 11 | Nut for terminal transmitter | Engine | 3 | ||
3H2865 | F 44 | Rollers - needle bearing - gear change column | Gearbox | 1 | ||
3H2914 | E 10 | Spring - thrust - yellow = 7H 3212 | Clutch | 12 | ||
3H2963 | EE 128 | Clip - pipe to control unit & adaptor = ACA 5119 | Clutch | 1 | ||
7H1698 | AE 2 | Seal ( bottom ) - oil filter - Purolator | Engine | 10 | ||
7H1701 | AE 11 | Seal ( bottom ) - oil filter - A.C. | Engine | 3 | ||
7H1764 | AF 4 | Sping- oil filter | Engine | 2 | ||
7H1948 | AE 18 | Seal - bottom - oil filter - Tecalemit | Engine | 8 | ||
7H1968 | AF 12 | Washer - felt - oil filter | Engine | 3 | ||
7H3001 | E 3 | Retainer - release lever plate | Clutch | 6 | ||
7H3048 | E 15 | Retainer -ring - assembly | Clutch | 2 | ||
7H3067 | E 4 | Pin - release lever - cover assembly | Clutch | 2 | ||
7H3069 | E 6 | Strut - cover assembly | Clutch | 12 | ||
7H3171 | E 5 | Spring - anti-rattle - cover assembly | Clutch | 8 | ||
7H3212 | E 10 | Spring - thrust - yellow = 3H 2914 | Clutch | 6 | ||
7H3213 | E 8 | Plate - release lever - cover assembly | Clutch | 4 | ||
7H5028 | N 14 | Brush | Dynamo | 1 | ||
7H5031 | N 15 | Spring - brush tension | Dynamo | 3 | ||
7H5042 | N 35 | Bush - commutator end = 47H 5340 | Starter | 9 | ||
7H5043 | N 26 | Sping - brush tension | Starter | 2 | ||
7H5046 | N 37 | Pinion & barrel = 67H 5010 | Starter | 1 | ||
7H5049 | N 37 | Bush - driving end = 47H 5346 | Starter | 2 | ||
7H5086 | page A 25 | Rotor arm | Engine service kit | 2 | ||
7H5130 | N 23 | Bruch set - wiper | Windscreen wipers | 5 | ||
7H5387 | N 16 | Bracket - commutator end | Dynamo | 1 | ||
7H5390 | N 17 | Bush - bearing ( for bracket ) | Dynamo | 4 | ||
7H5529 | N 31 | Sleeve - screwed ( with control nut ) = 67H 5013 | Starter | 1 | ||
7H7004 | EA 3 | Cup for piston | Clutch slave cylinder | 1 | ||
7H7025 | EH 14 | Washer - piston retainer | Brake master cylinder | 1 | ||
7H7436 | EH 3 | Gasket for plu | Brake master cylinder | 1 | ||
7H7925 | M 20 | Piston | Clutch brake master cylinder | 2 | ||
7H7928 | HA 16 | Piston - hydraulic | Rear brakes | 3 | ||
7H7938 | K 45 | Filler cap - front | Front suspension & brakes | 8 | ||
7H7940 | HA 18 | Filler - cup | Rear brakes | 2 | ||
7H9830 | NA 13 | Lock - barrel = 2H 4185 | Switches | 1 | ||
12H650 | page A 25 | Spring - valve = 1G 2887 | Engine | 28 | ||
13H153 | NE 17 | Relay box = 11K 9380 | Horns | 1 | ||
17H575 | AG 55 | Transmitter - thermal | Transmitter | SOLD OUT | ||
17H689 | O 63 | Cable - ( inner ) | Speedometer | 1 | ||
17H847 | AF 11 | Seal - valve - oil filter - Tecalemit | Engine | |||
17H1447 | AF 33 | Seal - oil filter - Purolater | Engine | 8 | ||
17H1556 | AF 26 | Ring - sealing - PUROLATER | Oil filter | 2 | ||
17H5106 | page B 1 | Sundry parts | Distributor | 1 | ||
17H5231 | NB 8 | Spring - trimmer | Headlamp | 4 | ||
17H5255 | NE 24 | Armature | Windscreen wiper | 1 | ||
17H5379 | NE43 | Wiper arm - LH - LUCAS 741839 | Windscreen wipers | 5 | ||
17H5433 | N 19 | Terminal assembly - dynamo | Engine equipment | 1 | ||
17H7707 | HA 15 | Seal | Rear brakes | |||
22H15 | page F 11 | Bush - selector lever ( nylon ) | Gearbox | 2 | ||
22H29 | F 80 | Bush = 11G 3227 = 2A 3256 | Gearbox | 2 | ||
27H3157 | E 7 | Eyebolt & nut | Clutch | 8 | ||
27H3279 | E 2 | Lever - release | Clutch | 3 | ||
27H5354 | NB 14 | Nut - rim fixing screw | Headlamps | 8 | ||
37H5250 | ND 27 | Cover for motif | Trafficators & horn | 4 | ||
37H5251 | ND 24 | Lever - trafficator switch = AJH 5116 | Trafficator & horn details | 1 | _ | |
37H5252 | ND 26 | Motif | Trafficators & horn | 5 | ||
37H5379 | NB 25 | Screw - rim fixing | Road lamps | 18 | ||
37H5452 | NC 16 | Interior bulb holder - flasher | Lamps | 4 | ||
47H5100 | page N 2 | Circlip - pinion & sleeve retaining | Starter | 4 | ||
47H5126 | NB 23 | Adaptor | Headlamp | 1 | ||
47H5340 | N 2 | Bush - commutator end = 7H 5042 | Starter | N 35 | ||
47H5346 | N 37 | Bush - driving end = 7H 5049 | Starter | 2 | ||
57H5291 | NE 43 | Wiper arm - LH = ADH 5492 | Windscreen pipers | 2 | ||
67H5010 | N 28 | Pinion & barrel = 7H 5046 | Starter | 2 | ||
67H5013 | N 31 | Sleeve - screwed ( with control nut ) = 7H 55129 | Starter | 1 | ||
1K372 | AB 17 | Circlip for valve cotter | Engine | 26 | ||
1K800 | AB 16 | Cotter for valves ( halves ) | Engine | 45 | ||
1K2142 | AF 40 | Screw for banjo unio - oil filter | Engine | 8 | ||
2K4909 | F 93 | Spring - column gear change = 22A 75 | Gearbox | 14 | ||
2K5197 | AC 16 | Washer for screw ( plain ) | Engine | 7 | ||
2K5774 | EB 7 | Washer for screw = 2K 6059 | Engine | 16 | ||
2K6059 | EB 7 | Washer for screw = 2K 5774 | Engine | 16 | ||
2K6343 | AB 19 | Plug for rocker shaft = 6K878 | Engine | 1 | ||
2K7477 | H 45 | Bearing for hub | Rear axle | 2 | ||
2K8169 | A 2 | Plug - welch | Engine | 2 | ||
2K8568 | AB 55 | Bush for cover ( rubber ) | Engine | 6 | ||
2K8686 | EA 22 | Nut for connector ( lock ) | Clutch slave cylinder | 2 | ||
2K8788 | EB 9 | Washer for screw ( lock ) | Engine | 16 | ||
2K8960 | F 67 | Spring for locking pg | Gearbox | |||
6K49 | page A 21 | Key - water pump | Engine | 1 | ||
6K499 | F 4 | Dowel for side cover | Gearbox | 1 | ||
6K501 | page A 19 | Washer for adaptor | Oil filter | 2 | ||
6K528 | F 89 | Bearing - 3rd & 4th motion shaft - rear | Gearbox | 1 | ||
6K650 | B 36 | Tube nut - distributor end | Distributor | 3 | ||
6K853 | AD 23 | Spring - release valve- oil pump | Engine | 3 | ||
6K878 | AB 19 | Plug for rocker shaft = 2K 6343 | Engine | 1 | ||
6K886 | F 37 | Spring - ring for bearing | Gearbox | 2 | ||
6K906 | EB 6 | Washer for screw - lock | Engine mounting plate | 8 | ||
6K912 | FB 114 | Ring - felt - gear change column | Gearbox | 3 | ||
11K9380 | NE 17 | Relay box = 13H 153 | Horns | 1 | ||
51K252 | A 14 | Stud for cylinde head - longer = 51K 891 | Engine | 4 | ||
51K253 | A 15 | Stud for cylinder head - short = 51K 892 | Engine | 9 | ||
51K891 | A 14 | Stud for cylinder head - longer = 51K252 | Engine | 4 | ||
51K892 | A 15 | Stud for cylinder head - short = 51K 253 | Engine | 9 | ||
51K893 | AB 6 | Stud for rocker bracket - long | Engine | 1 | ||
51K1178 | AB 27 | Locknut - tappet adjusting screw | Engine | 1 | ||
51K 1388 | AA 3 | Screw for cap - connecting rod | Engine | 4 | ||
PPP0632 | RJ 17 | Bumper bolt - chrome - bladeends to wing - crosshead phillips | Bumpers & fittings | SOLD OUT | ||
133602 | Overrider | Bumpers & fittings | 1 | |||
185839 | RG 94 | Pull & arm rest - (Empire green) = AAA4144 | Door hinges - Checks - Locks & Trim | 2 | ||